IAPMO RESEARCH AND TESTING, INC.
5001 E. Philadelphia Street, Ontario, CA 91761-2816 • (909) 472-4100 • Fax (909) 472-4244 • www.iapmort.org
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction.
| Effective Date: | January 2013 -Rev. 1/18/2013- | Void After:
January 2014
|
| Product: | Ceramic Plumbing Fixtures | File No. 1455 |
| Issued To: | MANSFIELD PLUMBING PRODUCTS ATTN: ACCOUNTS PAYABLE P. O. BOX 620 PERRYSVILLE, OH 44864-0620 |
|
| Identification: | Ceramic Plumbing Fixtures shall be marked with the manufacturer’s name or registered trademark, or in the case of private labeling, the name of the customer for whom the fixture was manufactured. Markings shall be permanent, legible, and visible after installation. The model number of close-coupled water closets shall be marked on both the tank and the bowl. Water closets and urinals shall be marked to identify the average water consumption, expressed in litres and gallons per flush. The litre or gallon value may be stated first, at the manufacturer’s option. Gravity flush tanks shall be marked with a water level mark or with the information necessary to determine the water level in the tank needed to deliver the intended flush volume. This mark shall be applied to the ceramic body of the tank, the tank liner, or the flush valve overflow tube. The vertical distance between the water level mark and the lowest point of the tank overflow channel shall not exceed 38 mm (1.5 in). Water closet tanks shall have a label indicating at least the following: (a) the telephone number or contact information of a service department from which end-users can obtain replacement parts; (b) the serial or part number of the flush valve seal; and (c) information on procuring replacement parts for maintaining the original flush volume. All packaging shall be marked with the manufacturer’s name or registered trademark; or in case of private labeling, the name of the customer for whom the fixture was manufactured and the model number. Packaging for water closets and urinals shall be marked with the water consumption in gpf and Lpf. Each fixture shall be marked with the cUPC® certification mark. In the case where the tank and the bowl are sold separately, both shall have the certification mark. Fixtures that require proprietary (i.e., non-standard) components, e.g., supply fittings, waste fittings, or water closet seats, shall indicate, in the packaging or the accompanying literature, that such components are provided by the manufacturer and shall identify the proper replacement parts. Fixtures that do not comply with one or more of the dimensional requirements of this Standard shall be marked with an “N” to indicate the non-standard nature of the fixture. |
|
| Characteristics: | Ceramic plumbing fixtures may include water closets, lavatories, urinals, bidets, service sinks and drinking fountains. To be installed in accordance with the manufacturer's instructions, the latest edition of the Uniform Plumbing Code, and the National Plumbing Code of Canada.
Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
|
|
|
Products are in compliance with the following code(s):
|
||
|
Uniform Plumbing Code (UPC®)
National Plumbing Code of Canada International Plumbing Code (IPC®) |
||
|
Products are in compliance with the following standard(s):
|
||
|
ASME A112.19.2-2008/CSA B45.1-08 including Update No. 2 dated March 2011
|
||
| ||
| ||
|
MODELS: MODELS: W A T E R C L O S E T
S: MODEL NO. DESCRIPTION/NAME CLASS GPF 101/102 Bowl#101/Tank#102 L/C 1.6 101/109 Bowl#101/Tank#109 L/C 1.6 1013-1012 Two-piece water closet L/C 1.1 1018 18" High Rear Spud
Bowl W/S 3.5 103/102 Bowl#103/Tank#102 L/C 1.6 103/109 Bowl#103/Tank#109 L/C 1.6 104/102 Bowl#104/Tank#102 L/C 1.6 104/109 Bowl#104/Tank#109 L/C 1.6 1080 Rear Spud Bowl W/S 3.5 111/112 Bowl#111/Tank#112 L/C 1.28 113/112 Bowl#113/Tank#112 L/C 1.28 114/112 Bowl#114/Tank#112 L/C 1.28 115/106 Bowl#115/Tank#106 L/C 1.6 117-160 Round Bowl#117/Tank#160 L/C 1.6 130/125 Bowl#130/Tank#125 Round Front L/C 1.6 130/160 ANSI Bowl#130/Tank#160 L/C 1.6 130/160 w/M400 Bowl#130/Tank#160 L/C 1.6 130/161 Bowl#130/Tank#161 Round Front L/C 1.6 130/162 Bowl#130/Tank#162 L/C 1.6 130/164 Bowl#130/Tank#164 L/C 1.6 130/173 Bowl#130/Tank#173 L/C 1.6 130/189 Bowl#130/Tank#189 Round Front L/C 1.6 130/199 Bowl#130/Tank#199 Round Front L/C 1.6 1300 Wall Hung W/L 1.6 1301 One piece L/C 1.28 1301 BPL One piece, wall hung L/C 1.28 130CTK Bowl#130/Tank#160 L/C 1.6 131/160 Bowl#131/Tank#160 L/C 1.6 131/160 w/M400 Bowl#131/Tank#160 L/C 1.6 131/164 Bowl#131/Tank#164 L/C 1.6 1310 Rear Spud Bowl L/C 1.6 1311 Flushometer
ADA Height
L/C 1.6 1311RS Flushometer
Elongated Front HET 1.28 1312 Flushometer
Elongated Front L/C 1.6 1313 One piece, elongated, rear
outlet HET 1.28 1317 Handicap Flushometer
Elongated Bowl L/C 1.6 1318 Flushometer
ADA Height
L/C 1.6 1319 One piece L/C 1.28 1319 BPL One piece L/C 1.28 1319RS Flushometer
Elongated ADA HET 1.28 132/163 Bowl#132/Tank#163 L/C 1.6 135/125 Bowl#135/Tank#125 Elongated L/C 1.6 135/160 Bowl#135/Tank#160 Elongated L/C 1.6 135/160 ANSI Bowl#135/Tank#160 L/C 1.6 135/160 w/M400 Bowl#135/Tank#160 L/C 1.6 135/161 Bowl#135/Tank#161 Elongated L/C 1.6 135/162 Bowl#135/Tank#162 L/C 1.6 135/164 Bowl#135/Tank#164 L/C 1.6 135/173 Bowl#135/Tank#173 L/C 1.6 135/189 Bowl#135/Tank#189 Round Front L/C 1.6 135/199 Bowl#135/Tank#199 Elongated L/C 1.6 135CTK Bowl#135/Tank#160 L/C 1.6 136/163 Bowl#136/Tank#163 L/C 1.6 137/160 Bowl#137/Tank#160 L/C 1.6 137/160 w/M400 Bowl#137/Tank#160 L/C 1.6 137/160-RH Bowl#137/Tank#160-RH L/C 1.6 137/164 Bowl#137/Tank#164 L/C 1.6 137/173 Bowl#137/Tank#173 L/C 1.6 137CTK Bowl#137/Tank#160 L/C 1.6 137NS-161 Elongated Bowl#137/Tank#161 L/C 1.6 138/160 Bowl#138/Tank#160 L/C 1.6 138/164 Bowl#138/Tank#164 L/C 1.6 139NS-160 Elongated Bowl#139/Tank#160 L/C 1.6 140/120 Bowl#140/Tank#120 L/C 1.6 141/120 Bowl#141/Tank#120 Elongated L/C 1.6 142/127 Bowl#142/Tank#127 Elongated L/C 1.6 144/123 Bowl#144/Tank#123 Elongated 144/153 Bowl#144/Tank#153 Elongated 145/121 Pseudo One Piece 12"
Rough-In L/C 1.6 146/122 Bowl#146/Tank#122 L/C 1.6 146/123 Bowl#146/Tank#123 L/C 1.6 146/153 Bowl#146/Tank#153 Pressure
Assisted 1.0 146/154 Bowl#146/Tank#154 Pressure
Assisted 1.0 146/35 Bowl#146/Tank#35 W/S 3.5 147-122 Bowl#147/Tank#122 L/C 1.6 147-123 Bowl#147/Tank#123 L/C 1.6 147-153 Bowl#147/Tank#153 Pressure
Assisted 1.0 147-154 Bowl#147/Tank#154 Pressure
Assisted 1.0 148-122 Bowl#148/Tank#122 L/C 1.6 148-123 Bowl#148/Tank#123 L/C 1.6 148-153 Bowl#148/Tank#153 Pressure
Assisted 1.0 148-154 Bowl#148/Tank#154 Pressure
Assisted 1.0 149-123 Bowl#149/Tank#123 Pressure Assisted 1.6 149-153 Bowl#149/Tank#153 Pressure
Assisted 1.0 *150-1 Bowl#150/Tank#1 L/C 1.6 *150-1-LH Bowl#150/Tank#1 L/C 1.6 151-123 Bowl#151/Tank#123 L/C 1.6 151-153 Bowl#151/Tank#153 HET 1.1 158-1 Bowl#158/Tank#1 L/C 1.6 158-1-LH Bowl#158/Tank#1 L/C 1.6 158-1-RH Bowl#158/Tank#1 L/C
1.6 184-185 Bowl#184/Tank#185 L/C 1.6 186-187 Bowl#186/Tank#187 L/C 1.6 186-188 Bowl#186/Tank#188 L/C 1.6 380/386 Round Bowl#380/Tank#386 L/C 1.6 380-3386 Bowl#380/Tank#3386 L/C 1.6 380-387 Bowl#380/Tank#387 HET 1.28 380-387-1.1GPF Elongated Bowl#380/Tank#381 HET 1.1 380CTK Bowl#380/Tank#3386 L/C 1.6 382/386 Bowl#382/Tank#386 L/C 1.6 382-3386 Bowl#382/Tank#3386 L/C 1.6 382-387 Bowl#382/Tank#387 HET 1.28 382-387-1.1GPF Round Bowl#382/Tank#387 HET 1.1 382CTK Bowl#382/Tank#386 L/C 1.6 384/386 Elongated Bowl#384/Tank#386 L/C 1.6 384-3386 Bowl#384/Tank#3386 L/C 1.6 384-387 Bowl#384/Tank#387 HET 1.28 384CTK Bowl#384/Tank#3386 L/C 1.6 390-392 Bowl 390/Tank 392 L/C 1.6 4115-3106 Bowl#4115/Tank#3106 HET 1.28 4117-160 Round Bowl#4117/Tank#3121 HET 1.28 4130-128 Bowl#4130/Tank#128 L/C 1.28 4130-3121 Bowl#4130/Tank#3121 L/C 1.28 4130CTK Bowl#4130/Tank#3121 L/C 1.28 4131-3121 Round Bowl#4131/Tank#311 HET 1.28 4135-128 Two-piece water closet L/C 1.28 4135-3121 Two-piece water closet L/C 1.28 4135CTK Two-piece water closet L/C 1.28 4137-3121 Two-piece close-couple, Elongated
bowl L/C 1.28 4137CTK Two-piece close-couple, Elongated
bowl L/C 1.28 4138-3121 Elongated Bowl#4138/Tank#3121 HET 1.28 4147-3147 Bowl#4147/Tank#3147 4197-3195 Two-piece water closet L/C 1.28 4380CTK Round Bowl#380/Tank#386 L/C 1.6 4382CTK Bowl#382/Tank#3386 L/C 1.6 4384CTK Bowl#384/Tank#3386 L/C 1.6 4810-3816 Two-piece water closet HET 1.28 4817-3816 Two-piece
water closet HET
1.28 700 One Piece L/C 1.6 704 One Piece, Elongated 705 One Piece L/C 1.6 705NS One Piece, Elongated L/C 1.6 708 One piece HET L/C 1.28/1.6 MPP702 Elongated Front, Low Profile
One-Piece L/C 1.6 MPP707 Elongated Front, Low Profile Smart
Height, One Piece L/C 1.6 MPP722 Elongated Front, Low Profile
One-Piece L/C 1.6 WC5060 Round Front, One-Piece L/C 1.6 WC5065 Elongated Front, One-Piece L/C 1.6 WC5080 Elongated Front, One-Piece L/C 1.6 U R I N A L S MODEL NO. DESCRIPTION CLASS GPF 401 L/C .71 410
L/C 1.0 410 Top Spud, Rear Outlet, HEU 0.5 gpf 410 R/S Rear Spud, Rear Outlet, HEU 0.5 gpf 421 Wall hung L/C 1/8 422 Top Spud, Wall Mount HEU 0.11 gpf 422 R/S Wall Hung HEU 0.11 gpf 475 With Integral Trap L/C 1.0 *A minimum water supply
pressure of 20 psi is required at the fixture. *These units have been listed
by IAPMO under the first paragraph of Section 5 of ANSI 112.19.2M-1982. L A V A T O R I E S 216, 217, 218NS, 226, 242,
249, 250, 251, 252, 257, 259, 267, 268, 269, 270 (w/Optional 273 Base Pedestal),
280, 285, ▲290, ▲292, 297, 299, 300, 303, 305, 310, 311,
312, 315, 318(w319 Base Pedestal), 328, 329, 333, 334, 338, 339, 344, 348, 800,
802, 805, 826, 1613NS, 1917C, 2008, ▲2018C-NS (w/optional 293 Base
Pedestal), 2018HB & 2018HB-NS, MS1290, MS1390,453, 2038 W/ 2039 SHROUD, 315
L/O, 2018HB L/O, 1917C L/O, 2028, 234, 254 P E D E S T A L S Model No. Description 303 To be used with the following
lavatories: 272, 292, 300, 2018C 304 To be used with the following
lavatories: 292, 300, 2018C 305 To be used with the following
lavatories: 292, 300, 2018C 319 To be used with the following lavatory:
318 (Combination number 320) 413 To be used with the following
lavatories: 453 438 ▲ = With optional #294 pedestal base. |
||
|
ADDITIONAL COMPANY INFO: American Standard Colceramica CoronaTM, MancesaTM,
Mancesa by MansfieldTM 2560/4560 2570/4560 137/4560 306 1318 2103-4112 1902 1900 4300 7440 Sanitarios Azteca S.A. De C.V. (Lamosa
Vortens) W A T E R C L O S E T S: Model No. Description/Name CLASS GPF 7003 Wall Hung
W/L 1.6 L A V A T O R I E S 7603 7604 7605 |
||
|
