IAPMO RESEARCH AND TESTING, INC.

5001 E. Philadelphia Street, Ontario, CA 91761-2816 • (909) 472-4100 • Fax (909) 472-4244 • www.iapmort.org





CERTIFICATE OF LISTING

IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction.

The most updated information on this Certificate of Listing is available online at pld.iapmo.org


 

Effective Date:
November 2013        
Void After: November 2014
     
Product: Bathtubs (Plastic) 
File No. 2719
     
Issued To: MANSFIELD PLUMBING PRODUCTS
1505 INDUSTRIAL DRIVE
HENDERSON, TX  75652
     
Identification:
Manufacturer's name or trademark, or both, shall be permanently and legibly marked on the unit so as to be visible after installation. The product or the product container shall also bear the UPC® certification mark.
     
Characteristics:
One piece plastic bathtubs to be installed in accordance with the manufacturer's instructions affixed to the unit and the requirements of the latest edition of the Uniform Plumbing Code.  The bathtubs are manufactured with or without walls and with right or left hand outlets. Bathtubs without factory applied nailing flanges are listed as drop-in units only, and are not to be installed against the wall. Bathtubs intended for installation against a wall shall incorporate an integral, factory applied or field applied nailing flange in accordance with the latest edition of CSA B45.5/IAPMO Z124.

Whirlpool piping is not included in this listing. Piping, if installed, must carry a separate IAPMO listing.

TILE FLANGE KITS:  The use of a listed tile flange kit allows installation against the wall.

Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
     
Products are in compliance with the following code(s):
 
Uniform Plumbing Code (UPC®)
International Plumbing Code (IPC®)
 
Products are in compliance with the following standard(s):
 
CSA B45.5-11/IAPMO Z124-2011

 

 

models_0002719

 MODELS:

 

Ambria        - 6060-AB       

Avalon        - 4272-AVB      

Barrett Alcove-3260-BA        

Baywood 5.0   - 3660 BWB      

Baywood 5.5   — 3666-BWB      

Baywood 6.0   — 3672-BWB      

Brentwood       3666 BDBT

Brentwood       3660 BDBT

Brentwood       3672 BDBT

Brentwood       4272 BDBT

Bristol Bay   — 6060-BBB      

Davanti       - 6060-DB       

Fiabo         - 4266-FB       

Lombardi      - 4472-LB       

3666-SB

Verdi          -  4260-VB

Verona         -  7272-VB

6060 DL        -  6060 DLB

3260            (Same as 3260A)

3260 TFS        (Same as 3260 TFSA)

3660            (Same as 3660A)

3660 TFS        (Same as 3660 TFSA)

3672            (Same as 3672A)

4260 — OV       (Same as 4260 OVA)

4260            (Same as 4260A) 

4260 — TFS      (Same as 4260 TFSA)

4272            (Same as 4272A)

4860            (Same as 4860A)

4872            (Same as 4872A)

6060            (Same as 6060A)