IAPMO RESEARCH AND TESTING, INC.
5001 E. Philadelphia Street, Ontario, CA 91761-2816 • (909) 472-4100 • Fax (909) 472-4244 • www.iapmort.org
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction.
| Effective Date: | April 2013 | Void After:
April 2014
|
| Product: | California Lead Plumbing Law – Devices and Components | File No. 6072 |
| Issued To: | BRADLEY CORPORATION W142 N9101 FOUNTAIN BOULEVARD MENOMONEE FALLS, WI 53051-2348 |
|
| Identification: | Each product shall bear permanent and legible markings to identify the manufacturer. This marking shall be the trade name, trademark, or other mark known to identify the manufacturer. The product and/or product packaging may also bear the term "Lead Plumbing Law", "Complies with Lead Plumbing Law", or "Low-Lead" above or in close proximity to the appropriate IAPMO R&T certification mark, or the term "Certified by IAPMO R&T". The product packaging may also bear a grey dot, a check mark with circle, or any other home centers marking requirements. | |
| Characteristics: | Products listed below are to be installed in accordance with the manufacturer's instruction. These products have been verified with weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
|
|
|
Products are in compliance with the following standard(s):
|
||
|
Section 116875 of the California Health & Safety Code
|
||
| ||
| ||
|
MODELS: NPT Inlet and Outlet Model No. Size S53-34l TL 900AZ Futura-Accu-Zone-4" Centerset with Tempered Line S53-341 TMA 900AZ Futura-Accu-Zone-4" Centerset with TMV Valve S53-342 900AZ Futura-Accu-Zone-4" Centerset without Valve S53-343TL 900AZ Futura-Accu-Zone-Centershank with
Tempered Line S53-343TMA 900AZ Futura-Accu-Zone-Centershank with TMV
Valve S53-344 900AZ Futura-Accu-Zone-Centershank without
Valve S53-345TL 900AZ Futura-Accu-Zone-Centershank with
Tempered Line and 8" Trim Plate S53-345TMA 900AZ Futura-Accu-Zone-Centershank with TMV
Valve and 8" Trim Plate S53-346 900AZ Futura-Accu-Zone-Centershank without
Valve and 8" Trim Plate S59-2025 3/4" Inlet and 3/4" Outlet S59-2045 3/4" Inlet and 1" Outlet S59-2080 1" Inlet and 1-1/4" Outlet S59-2130 1/4" Inlet and 1-1/2" Outlet S59-2200 2"
Inlet and 2" Outlet S59-3045 3/4" Inlet and 1" Outlet S59-3080 1" Inlet and 1-1/4" Outlet S59-3130 1/4" Inlet and 1-1/2" Outlet S59-3200 2" Inlet and 2" Outlet S59-4000 1/2" NPT S59-4000A 3/8" Compression S59-4000BY Thermostatic Mixing Valve w/by-pass tee,
3/8" compression S59-4016 S59-4016N S59-4016S S59-4016X S59-4016Y THE FOLLOWING MODELS COMPLY
WITH NSF/ANSI 61 — ANNEX G: MODELS: Model No. Description S53-341TL 900AZ Futura-Accu-Zone-4" Centerset with Tempered Line S53-341TMA 900AZ Futura-Accu-Zone-4" Centerset with TMV Valve S53-342 900AZ Futura-Accu-Zone-4" Centerset without Valve S53-343TL 900AZ Futura-Accu-Zone-Centershank with
Tempered Line S53-343TMA 900AZ Futura-Accu-Zone-Centershank with TMV
Valve S53-344 900AZ Futura-Accu-Zone-Centershank without
Valve S53-345TL 900AZ Futura-Accu-Zone-Centershank with
Tempered Line and 8" Trim Plate S53-345TMA 900AZ Futura-Accu-Zone-Centershank with TMV
Valve and 8" Trim Plate S53-346 900AZ Futura-Accu-Zone-Centershank without
Valve and 8" Trim Plate |
||
|
