IAPMO RESEARCH AND TESTING, INC.

5001 E. Philadelphia Street, Ontario, CA 91761-2816 • (909) 472-4100 • Fax (909) 472-4244 • www.iapmort.org





CERTIFICATE OF LISTING

IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction.


 

Effective Date: October 2012        
Void After: October 2013
     
Product: Cast Iron Soil Pipe and Fittings (Hubless) 
File No. 6384
     
Issued To: THERMAFIT INDUSTRIES INC.
723 SONORA AVE #B
GLENDALE, CA  91201
     
Identification: Each length of pipe and each fitting shall be plainly marked with the country of origin, the manufacturer’s name or the manufacturer’s registered trademark by which the manufacturer can be readily identified after installation. The marking shall be adequate identification of the manufacturer of the pipe and fittings of it readily identifies the manufacturer to the end user of the product.

Pipe markings:  The pipe shall be marked continuously on the barrel with a minimum of 0.75 inch (19mm) lettering starting within 3 inches of each end of the pipe.  Each pipe shall be marked with the date of manufacture. The marking shall be stenciled on the pipe or otherwise applied so as to be clear and legible.

Fitting markings:  The marking shall be cast with raised letters that are not to be located within the “W” dimension.  Cast markings shall be raised from the wall of the fitting unless otherwise noted.

Listed products shall bear the UPC® certification mark.
     
Characteristics: Hubless cast iron soil pipe and fittings for sanitary and storm drain, waste and vent piping application. To be used in gravity flow, non-pressure application. To be installed in accordance with the requirements of the latest edition of the Uniform Plumbing Code.

Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
     
Products are in compliance with the following code(s):
 
Uniform Plumbing Code (UPC®)
International Plumbing Code (IPC®)
 
Products are in compliance with the following standard(s):
 
ASTM A888-2011 (excluding Annex A1)

 

 

models_0006384

 MODELS:

Model No.    Description

156          1-1/2" X 10 FT NO HUB PIPE

158          2" X 10 FT NO HUB PIPE

160          3" X 10 FT NO HUB PIPE

162          4" X 10 FT NO HUB PIPE

164          5" X 10 FT NO HUB PIPE

168          6" X 10 FT NO HUB PIPE

170          8" X 10 FT NO HUB PIPE

0188         1/4 Bend 1-1/2"

0190         1/4 Bend 2"

0192         1/4 Bend 3"

0194         1/4 Bend 4"

0196         1/4 Bend 5"

0198         1/4 Bend 6"

0200         1/4 Bend 8"

0218         Reducing 1/4 Bend 4" X 3"

0236         1/4 Bend With Side Opening 3" X 2"

0238         1/4 Bend With Side Opening 4" X 2"

0280         1/4 Bend With Heel Opening 3" X 2"

0282         1/4 Bend With Heel Opening 4" X 2"

0275         Low Heel 1/4 Bend extended 3" X 2"

0277         Low Heel 1/4 Bend extended 4" X 2"

0326         Tapped 1/4 Bend 1-1/2" X 1-1/2"

0330         Tapped 1/4 Bend 2" X 1-1/2"

0332         Tapped 1/4 Bend 2" X 2"

0402         Double 1/4 Bend 2"

0404         Double 1/4 Bend 3"

0406         Double 1/4 Bend 4"

0425         Long 1/4 Bend 2" X 18"

0462         Short Sweep 2"

0464         Short Sweep 3"

0468         Short Sweep 4"

0470         Short Sweep 5"

0472         Short Sweep 6"

0474         Short Sweep 8"

0475         Short Sweep 10"

0476         Short Sweep 12"

0477         Short Sweep 15"

0492         Long Sweep 1-1/2"

0494         Long Sweep 2"

0496         Long Sweep 3"

0498         Long Sweep 4"

0500         Long Sweep 5"

0502         Long Sweep 6"

0536         1/5 Bend 2"

0538         1/5 Bend 3"

0540         1/5 Bend 4"

0570         1/6 Bend 2"

0572         1/6 Bend 3"

0574         1/6 Bend 4"

0576         1/6 Bend 6"

0578         1/6 Bend 8"

0604         1/8 Bend 1-1/2"

0606         1/8 Bend 2"

0608         1/8 Bend 3"

0610         1/8 Bend 4"

0612         1/8 Bend 5"

0614         1/8 Bend 6"

0616         1/8 Bend 8"

0617         1/8 Bend 10"

0618         1/8 Bend 12"

0619         1/8 Bend 15"

0676         1/16 Bend 1-1/2"

0678         1/16 Bend 2"

0680         1/16 Bend 3"

0682         1/16 Bend 4"

0684         1/16 Bend 5"

0686         1/16 Bend 6"

0688         1/16 Bend 8"

806          Sanitary Tee Branch 1-1/2"

 

808         Sanitary Tee Branch 2" X 1-1/2"

810         Sanitary Tee Branch 2 "

812         Sanitary Tee Branch 3" X 1-1/2"

814         Sanitary Tee Branch 3" X 2"

816         Sanitary Tee Branch 3"

818         Sanitary Tee Branch 4" X 2"

820         Sanitary Tee Branch 4" X3"

822         Sanitary Tee Branch 4"

824         Sanitary Tee Branch 5" X 2"

826         Sanitary Tee Branch 5" X 3"

828         Sanitary Tee Branch 5" X 4"

830         Sanitary Tee Branch 5"

832         Sanitary Tee Branch 6" X 2"

838         Sanitary Tee Branch 6" X 3"

834         Sanitary Tee Branch 6" X 4"

835         Sanitary Tee Branch 6" X 5"

836         Sanitary Tee Branch 6"

842         Sanitary Tee Branch 8" X 6"

844         Sanitary Tee Branch 8" X 5"

846         Sanitary Tee Branch 8" X 4"

840         SAN TEE 8"

1208        Sanitary Tapped Tee 1-1/2" X 1-1/4" .

1210        Sanitary Tapped Tee 1-1/2"

1212        Sanitary Tapped Tee 2" X 1-1/4"

1214        Sanitary Tapped Tee 2" X 1-1/2"

1216        Sanitary Tapped Tee 2"

1220        Sanitary Tapped Tee 3" X 1-1/2"

1222        Sanitary Tapped Tee 3" X 2"

1223        Sanitary Tapped Tee 3"

1226        Sanitary Tapped Tee 4" X 1-1/2"

1228        Sanitary Tapped Tee 4" X 2"

1312        Wye 1" X 1/2"

1314        Wye 2"

1313        Wye 2" X 1-1/2"

1315        Wye 3" X 1-1/2"

 

1316         Wye 3" X 2"

1318         Wye 3"

1320         Wye 4" X 2"

1322         Wye 4" X 3"

1324         Wye 4"

1326         Wye 5" X 2"

1328         Wye 5" X 3"

1330         Wye 5" X 4"

1332         Wye 5"

1334         Wye 6" X 2"

1336         Wye 6" X 3"

1338         Wye 6" X 4"

1340         Wye 6" X 5"

1342         Wye 6"

1346         Wye 8" X 3"

1348         Wye 8 X 4"

1350         Wye 8 X 5"

1352         Wye 8 X 6"

1354         Wye 8"

1357         Wye 10" X 4"

1358         Wye 10" X 5"

1359         Wye 10" X 6"

1360         Wye 10 " X 8"

1361         Wye 10"

1364         Wye 12" X 10"

1362         Wye12"

1363         Wye 15"

1536         Double Wye 1-1/2"

1538         Double Wye 2"

1540         Double Wye 3 X 2"

1542         Double Wye 3"

1544         Double Wye 4" X 2"

1546         Double Wye 4" X 3"

1548         Double Wye 4"

1550         Double Wye 5" X 4"

 

1552         Double Wye 6" X 4"

1646         Upright Wye 2"

1648         Upright Wye 3" X 2"

1650         Upright Wye 3"

1652         Upright Wye 4" X 2"

1654         Upright Wye 4" X 3"

1656         Upright Wye 4"

1694         Combination Wye and 1/8 Bend 1-1/2"

1696         Combination Wye and 1/8 Bend 2" X 1-1/2"

1698         Combination Wye and 1/8 Bend 2"

1700         Combination Wye and 1/8 Bend 3" X 2"

1702         Combination Wye and 1/8 Bend 3"

1704         Combination Wye and 1/8 Bend 4" X 2"

1706         Combination Wye and 1/8 Bend 4" X 3"

1708         Combination Wye and 1/8 Bend 4"

1710         Combination Wye and 1/8 Bend 5" X 2"

1712         Combination Wye and 1/8 Bend 5" X 3"

1714         Combination Wye and 1/8 Bend 5" X 4"

1716         Combination Wye and 1/8 Bend 5"

1718         Combination Wye and 1/8 Bend 6" X 2"

1720         Combination Wye and 1/8 Bend 6" X 3"

1722         Combination Wye and 1/8 Bend 6" X 4"

1724         Combination Wye and 1/8 Bend 6" X 5"

1726         Combination Wye and 1/8 Bend 6"

1728         Combination Wye and 1/8 Bend 8" X 4"

1730         Combination Wye and 1/8 Bend 8" X 5"

1732         Combination Wye and 1/8 Bend 8" X 6"

1734         Combination Wye and 1/8 Bend 8"

1802         Combination Wye and 1/8 Bend,Double 2"

1804         Combination Wye and 1/8 Bend,Double 3" X 2"

1808         Combination Wye and 1/8 Bend,Double 4" X 2"

1806         Combination Wye and 1/8 Bend,Double 3"

1810         Combination Wye and 1/8 Bend,Double 4" X 3"

1812         Combination Wye and 1/8 Bend,Double 4"

1850         Sanitary Cross 1-1/2"

1852         Sanitary Cross 2"

1854         Sanitary Cross 3" X 2"

1856         Sanitary Cross 3"

1858         Sanitary Cross 4" X 2"

1860         Sanitary Cross 4" X 3"

1862         Sanitary Cross 4"

1864         Sanitary Cross 6" X 4"

2014         Sanitary Cross, Tapped 2" X 11/4"

2016         Sanitary Cross, Tapped 2" X 1-1/2"

2018         Sanitary Cross, Tapped 2"

2022         Sanitary Cross, Tapped 3" X 1-1/2"

2024         Sanitary Cross, Tapped 3" X 2"

2028         Sanitary Cross, Tapped 4" X 1-1/2"

2030         Sanitary Cross, Tapped 4" X 2"

2046         Test Tee 2"

2048         Test Tee 3"

2050         Test Tee 4"

2052         Test Tee 5"

2054         Test Tee 6"

2056         Test Tee 8"

2138         Short, Increaser-Reducer 2 X 1-1/2"

2140         Short, Increaser-Reducer 3 X 2"

2142         Short, Increaser-Reducer 4 X 2"

2144         Short, Increaser-Reducer 4 X 3"

2146         Short, Increaser-Reducer 5 X 2"

2148         Short, Increaser-Reducer 5 X 3"

2150         Short, Increaser-Reducer 5 X 4"

2152         Short, Increaser-Reducer 6 X 2"

2154         Short, Increaser-Reducer 6 X 3"

2156         Short, Increaser-Reducer 6 X 4"

2158         Short, Increaser-Reducer 6 X 5"

2160         Short, Increaser-Reducer 8 X 2"

2162         Short, Increaser-Reducer 8 X 3"

2164         Short, Increaser-Reducer 8 X 4"

2166         Short, Increaser-Reducer 8 X 5"

 

2168         Short, Increaser-Reducer 8 X 6"

2172         Short, Increaser-Reducer 10 X 4"

2173         Short, Increaser-Reducer 10 X 5"

2174         Short, Increaser-Reducer 10 X 6"

2175         Short, Increaser-Reducer 10 X 8"

2176         Short, Increaser-Reducer 12 X 4"

2177         Short, Increaser-Reducer 12 X 6"

2178         Short, Increaser-Reducer 12 X 8"

2179         Short, Increaser-Reducer 12 X 10"

2181         Short, Increaser-Reducer 15 X 6"

2182         Short, Increaser-Reducer 15 X 8"

2183         Short, Increaser-Reducer 15 X 10"

2184         Short, Increaser-Reducer 15 X 12"

2244         Tapped Adapters 2" X 2"

2480         Blind Plug 1-112"

2482         Blind Plug 2"

2484         Blind Plug 3"

2486         Blind Plug 4"

2488         Blind Plug 5"

2490         Blind Plug 6"

2492         Blind Plug 8"

2494         Blind Plug 10"

2495         Blind Plug 12"

2496         Blind Plug 15"

2506         P Trap 1-112"

2508         P Trap 2"

2510         P Trap 3"

2512         P Trap 4"

2514         P Trap 6"

2524         Running Trap with Double Vents 4"

2564         Deep Seal P Trap 2"

2566         Deep Seal P Trap 3"

2567         Deep Seal P Trap 4"

2582         P Trap With Tapped Inlet 1-1/2"

2586         P Trap With Tapped Inlet 2" X 1-1/2"

2588         P Trap With Tapped Inlet 2"

 

2832         Closet Bend 3" X 4", 6" X 12"

2840         Closet Bend 3" X 4", 6" X 15"

2842         Closet Bend 3" X 4", 6" X 16"

2844         Closet Bend 3" X 4", 6" X 18"

2852         Closet Bend 3" X 4",10" X 12"

2860         Closet Bend 3" X 4", 10" XIS"

2864         Closet Bend 3" X 4",10" X 16"

2870         Closet Bend 3" X 4",16" X 16"

2872         Closet Bend 4" X 4" X 16" X 16"

2874         Closet Bend 4" X 4" X 6" X 12"

2908         Closet Bend 4", 6" X 15"

2910         Closet Bend 4", 6" X 16"

2924         Closet Bend 4", 10" X 12"

2932         Closet Bend 4", 10" X 15"

2934         Closet Bend 4", 10" X 16"

2973         Closet Flange 4x2 (caulk)

2975         Closet Flange 4x3 (caulk)

2980         Closet Flanges 4" X 2"(mechanical)

2981         Closet Flanges 4" X 3" (mechanical)

2982         Closet Flanges 4" X 4" (mechanical)

2966         Closet Flange Riser 4" X 3" X 3" -1/2"

7976         Closet Flange 4x4 (caulk)8002 Tapped Inlet, Double 2" X 2" X 1-1/2" X 1-1/2"

8052         Modified Combination Wye and 1/8 Bend, Double 2"

8054         Modified Combination Wye and 1/8 Bend, Double 3" X 2" X 3"

8056         Modified Combination Wye and 1/8 Bend, Double 3"

8058         Modified Combination Wye and 1/8 Bend, Double 4" X 2" X 4"

8062         Modified Combination Wye and 1/8 Bend, Double 4"

8442         Two-Way Cleanout 3" X 3" X 4"

8446         Two-Way Cleanout 4" X 4" X 4"

8548         P-Trap Reducing 3" X 2"

8530         P Trap with Primer 2"

8532         P Trap with Primer 3"

8534         P Trap with Primer 4"

8562         Iron Body Cleanout~Tapped 2" X 1-1/2 "(IBCO 2")

8564         Iron Body Cleanout- Tapped 3" X 2-1/2" (IBCO 3 ")

 

8566         Iron Body Cleanout-Tapped 4" X 3-1/2" (IBCO 4")

8570         Iron Body Cleanout- Tapped 6" X 5 1/2 "(IBCO 6")

9500         Vent Closet Tee or Cr9ss 4" X 4" X 2" X 4" R or L

9502         Vent Closet Tee or Cross 4" X 4" X 2" X 2" X 4" R or L

9504         Vent Closet Tee or Cross 4" X 4" X 2" X 4"

9505         Vent Closet Tee or Cross 4" X 4" X 2" X 2" X 4" X 4"

 
 





Print Certificate